BOUNDER ELECTRONICS

UE1GT Smart Brake Release Switch

UE1GT CBBC Circuit Breaker Battery Cable

UE1GT DHC T Left and Right Driver Hand Controls

• Light Touch - low force will move the joystick • Fully Proportional
• Sturdy diecast metal box with black powder coat finish
• Three high reliability switches: POWER, SELECT and AUX SW 1
• Multi-function 1/2" alphanumeric LED display (shows battery condition when driving, displays error codes and other user information)
• 3 Ultra-Brite LED's indicate BRAKE RELEASED, ERROR and ECU status
• 6 Ultra-Brite LED's indicate which DRIVE [A-F or attendant drive program AC ( slanted A)], ACCESSORY A-F or ECU channel (A or B) is active
• 7 Ultra-Brite LED's show the SA GROUP (Seating Actuator Group) selected

The POWER switch turns the electronics on and off, the joystick controls driving the chair. The bidirectional SELECT switch chooses any of 6 programs (A-F) when the chair is being driven. AUX SW 1 is programmable and can be used to control various accessories and functions. The BATTERY CONDITION meter shows the battery condition from 1 to 10 and also doubles as an ERROR CODE display. When the SELECT switch is operated, the display also shows the drive program or function for 1 second. If a charger is plugged in, the display shows a lower case "c" for charger. The built-in ammeter is toggled on and off by pressing the POWER switch down. The ammeter displays 1-15A in 1A increments; automatically turns off after 5 minutes.

STD RHC

Right hand control (standard - no up charge)

LHC

Left hand control (no up charge)

UE1GT DHC T

UE1GT Driver Hand Control with 3 toggle switches: POWER, SELECT & AUX 1

Remote Display separate from joystick & switches [typically used with a separate control that has a joystick and switches (e.g., chin control), specialty controls and sometimes attendant controls]

Adds a key switch at the front of the hand control (includes 2 keys)

Bib mount chin control (less bib & chincup)

Chin control with front facing switches (less mount & chincup)

Attendant control / dual control. Operates in addition to a Driver Control (DHC). Includes 3 swtches: POWER, SELECT and ACDC AUX SW.

Attendant control only (no driver control). An ACDC is installed instead of a Driver Hand Control. An RD can be added.

Custom hand, foot or chin control (tell us what you need!)

Standard hand control mount

Standard hand control extension slide

Swing away hand control mount (swings out to side and back). Very durable! Made of steel. See animation above.

Midline hand control extension slide (swings up to side) (specify left or right mount)

CC MOUNT

Chin control mounting bracket (specify left or right mount)

POWER CC MOUNT

Power chin control mount. Actuator swings chin control and boom to side about 90 degrees when control switch is operated. Bi-directional momentary toggle switch control is standard. Other custom control switches and methods of control are possible. (specify left or right mount) See animation below.

CC BIB MOUNT

Chin control bib mount

RECARO DHC MNT

Driver hand control mount attached to Recaro arm

CUS CTRL MOUNT

Custom control mount. Tell us what you need!

CUS EXT SLIDE

Custom extension slide (close in, straight, custom height, etc.)

UE1GT 24 volt drive module. Features 6 drive programs, 22 operating modes, 6 switch inputs, battery condition meter, error dectection system, built-in charger ammeter and detailed owner's manual.

UE1GT BRS

UE1GT Smart Brake Release Switch (plugs directly into drive module)

UE1GT Emergency Stop and Select Switch (plugs directly into drive module)

UE1GT Remote Power Switch (plugs directly into drive module)

UE1GT Auxiliary Switch (specify function). Plugs directly into drive module. Up to 2 can be added (AUX SW 2 and AUX SW 3).

UE1GT Plug-in Programmer

DX or PG Drives Programmable Electronics can be installed on chairs when appropriate. They are typically used for switch, sip & puff, and headrest array controlled chairs. ST4M&B-M are usually required to achieve the necessary high torque at very slow speeds. Top speed is limited to that appropriate for the user's capabilities and the type of controls that are installed. Two to five MPH is typical. Attendant controls, combined lighting and seating actuator module, specialty controls remote (with LCD screen on gooseneck mount), etc. are commonly installed. Contact the factory for additional information. DX and PG Drives Electronics are not recommended for those who can utilize our standard UE1GT electronics. DX and PG Drives Electronics are also not recommended for speeds above 6 MPH.

ASL Wheelchair Control Systems can be installed on chairs when appropriate. Headrest arrays (with or without sip & puff and lip switches), proximity switches, fiber optic arrays and beam switches can be used. DX or PG Drives electronics are normally installed with ASL controls. ST4M&B-M are usually required to achieve the necessary high torque at very slow speeds. Top speed is limited to that appropriate for the user's capabilities and the type of controls that are installed. Two to five MPH is typical. Attendant controls, combined lighting and seating actuator module, specialty controls remote (with LCD screen on gooseneck mount), etc. are commonly installed. Contact the factory for additional information. DX or PG Drives Electronics are not recommended for those who can utilize our standard UE1GT electronics. DX or PG Drives Electronics are also not recommended for speeds above 6 MPH. It is possible to use an ASL headrest array in conjunction with our standard UE1GT chin control systems to control a power seating actuator such as tilt or recline, or to control a power chin control mount (to move the chin control to and from the user's face).